Syslinux

Bedrock Linux itself is largely agnostic of which bootloader you choose to use. Syslinux installation is documented here rather than another bootloader primarily due to the fact it is relatively simple and easy to set up by hand. If you would prefer a different bootloader, such as GRUB or LILO, and you are confident you are able to set it up (with documentation from another source), you are welcome to use another bootloader. If you are dual booting with another operating system which has its own bootloader and you know how to add Bedrock Linux to the other operating system's bootloader, you are welcome to do that as well. If you are able to setup the system without a bootloader (e.g. leveraging EFI), that too is fine.

Syslinux is both the name of a project which contains multiple bootloaders and the name of one of the bootloaders within the project. If you are using ext2, ext3, ext4 or BTRFS as your filesystem, the "extlinux" bootloader from Syslinux should suffice. If you are using another filesystem, you can either look at another member of the Syslinux family which supports your filesystem or find a completely different bootloader. If you do choose to use a different syslinux bootloader, the steps should be largely the same, replacing "extlinux" with the bootloader of choice.

Download Syslinux from the official syslinux website. Be sure to read the specific pages for the given release in case there are any known issues. You should probably at least skim the contents of the doc/ directory in the tarball as well. If you are using BTRFS, you need at least version 4.0.

Note: These instructions were written for Syslinux 6.01. 6.02 - the latest at the time of writing - has been found to have issues chain.c32.

If you are not using a LiveUSB/LiveCD but are using another partition on the same machine as the one on which you are installing Bedrock Linux, avoid shutting down the installer host part-way through these instructions to avoid leaving yourself without a successfully set up bootloader.

Make a directory to install extlinux into:

mkdir /mnt/bedrock/boot/extlinux

Change to the directory in which you placed downloaded Syslinux source.

cd /mnt/bedrock/src

Unpackage syslinux and change directories into the extlinux subdirectory in it:

tar xvf syslinux-VERSION.tar.gz
cd syslinux-VERSION

Next, compile. If you are making this for non-EFI systems run:

make clean; make bios

If you are making it for 32-bit EFI systems, run:

make clean; make efi32

Or, if you are making it for 64-bit EFI systems, run:

make clean; make efi64

Remember which choice you made here, as you will need that information later.

You may receive an error about lacking nasm or uuid-dev or some other packages. If so, install those packages and try again.

You should now have an extlinux executable somewhere.

To find it, run

`find /mnt/bedrock/src/syslinux-VERSION -name extlinux -type f

cd to the directory containing the extlinux executable and then install it into Bedrock Linux:

./extlinux --install /mnt/bedrock/boot/extlinux

Although syslinux is installed on the partition, it still needs to be properly set up on the harddrive itself. Find the corresponding device file for device you made bootable when you partitioned/formatted earlier. Note that here we aren't looking for the partition device file - /dev/sdXN - but rather the device's file - /dev/sdX. There should be no 0-9 digit in the filename. As root:

Find the mbr.bin

find /mnt/bedrock/src/syslinux-VERSION -name mbr.bin -type f

If there are multiple results - one for each bios, efi32 and efi64 - use the one corresponding to which system you are using.

cd into the directory containing mbr.bin. Copy it over the desired drive's master boot record. Be very careful here.

cat ./mbr.bin > /dev/sdX # change X accordingly

Syslinux will need additional support files. You may read syslinux's documentation for what each of these do; however, unless you are short on disk space, it may be easiest to simply grab all of them. Again, like with mbr.bin, if there are multiple groups of results we want those corresponding to to your earlier choice of bios vs efi32 vs efi64. First, find the bios directory:

find /mnt/bedrock/src/syslinux-VERSION -name bios -type d # or efi32 or efi64 as used earlier
cd output-of-above

Next, copy all of the files ending in .c32 in this directory into the extlinux install directory.

find . -name "*.c32" -type f -exec cp {} /mnt/bedrock/boot/extlinux \;

Now you should create the configuration file for syslinux. Unlike GRUB, syslinux must be configured by hand. Assuming you want a graphical menu, run the following to get a basic menu in syslinux:

cat > /mnt/bedrock/boot/extlinux/extlinux.conf << EOF
UI menu.c32
MENU TITLE Syslinux Bootloader
DEFAULT bedrock
PROMPT 0
TIMEOUT 50

LABEL bedrock
    MENU LABEL Bedrock Linux 1.0beta1 Hawky
    LINUX ../vmlinuz-KERNEL-VERSION
    APPEND root=/dev/sdXN quiet ro
    INITRD ../initrd.img-VERSION
EOF

Consider changing the following:

Change vmlinuz-KERNEL-VERSION to the filename of kernel image that you installed.
Change the /dev/sdXN to the partition you set to boot - either Bedrock's main/root partition or its /boot partition if you made one.
If you either compiled an initrd or are using a kernel from another distribution which uses an initrd, you should probably include the INITRD ../initrd.img-VERSION line, changing the filename to the filename of the initrd. If you are not using an initrd and you are sure you have all of the modules required to boot built into the kernel you may leave the initrd line out of the file.
You may also change menu.c32 to vesamenu.c32 for a fancier menu or remove the UI menu.c32 line completely for a command line interface.

If you would like to dual-boot with another operating system such as Windows, append the following:

cat >> /mnt/bedrock/boot/extlinux/extlinux.conf << EOF
LABEL LABEL NAME
    MENU LABEL Operating System Name
    COM32 chain.c32
    APPEND hdN N
EOF

Consider changing the following from this addition:

The LABEL NAME is what Syslinux refers to this item - something short and simple such as "win7" should suffice.
The Operating System Name is what you will see for the item in the menu if you are using menu.c32 or vesamenu.c32. Something such as "Windows 7" should be fine.
Finally, hdN N refers to the hard drive (the first number) and partition (the second number) on which the bootloader you are chainloading is installed. It appears both numbers are zero-indexed, but if this does not work for you try with them either or both of them being one-indexed. For example, if the target operating system's bootloader is on /dev/sda1 (the first partition on the first harddrive), you will want hd0 0.

You should now have the syslinux bootloader installed. If it does not seem to work, consider installing a different syslinux release or trying out another bootloader.